My Cart


You have no items in your shopping cart.

Part # QTY:
Online Store

Category Navigation:

Customer Service

You're currently on:

Copper Plate On Steel Butterfly

Double click on above image to view full picture

Zoom Out
Zoom In

More Views

  • Copper Plate On Steel Butterfly
  • Gallon Copper Plate
  • Copper Plate On Steel Table

Copper Plate Gallon Metal Finishes Plus

Availability: In stock.

$50.64
Add Items to Cart
OR
  • |

Quick Overview

Gallon Copper Plate Metal Finish
Product Description






Description


 


Our copper plating solution plates steel and non-stainless steel alloys at room temperature without the need for any special equipment. This unique formula can be applied by immersion, spray, or by brush for detailed areas. The two mil thick plating produces a bright, shiny copper finish similar to the appearance of a new penny straight from the mint!


 


The color of the plated surface may be further altered by using our Rainbow Torch or Pewters. After plating and/or coloring, finished parts may be quick dried and sealed, or allowed to oxidize. Oxidation will alter the colors and textures, creating an additional palate of finish effects. The end results that may be achieved are only limited by your own imagination and artistic ability.


 


This solution is the basic building block for an unlimited range of beautiful, interesting looks never before available to steel finishers.


Primary use


 


Copper plate steel and non-stainless steel alloys


 


Secondary use


 


Copper plate steel for further treatment with other metal finishes


 


Application Method


 


For best results, steel being plated must be completely clean and free from all oils, mil plate, rust and any other contaminants.


 


Wear latex gloves if handling part by hand as finger oils will affect the plate quality.


 


Prep steel by sandblasting, pickling, grinding, wire brushing or sanding. Copper Plate will work on unclean steel, but uneven plating may occur.


 


Remove residual oils and dirt particles with mild detergent in solution. Rinse with water to remove soap residue.


 


Copper Plate may be applied either by spray or immersion, but immersion is recommended for even plating. Immersion time is normally 1-2 seconds resulting in a bright copper layer.


 


After plating, immediately rinse in a water bath to remove excess plating solution.


 


If desired, apply Rust Arrest to neutralize the chemical residue, allow Rust Arrest to remain for 20 seconds then rinse again.


 


At this point the finished part should be quick dried with compressed air or another method of your choice to avoid oxidation.


 


An alternate technique is to allow part to dry naturally and allow a slight amount of oxidization to form, altering the appearance and texture.


 


Once you dry your project completely, the part must be sealed with an appropriate topcoat such as acrylic sealer, wax, or clear powder coat, otherwise oxidation will eventually result.


 


Copper Plate can be used in conjunction with our Rainbow Torch, Dark Pewter and Light Pewter to radically alter the final appearance. If using one of these products along with Copper Plate, skip the Rust Arrest step until finished. See appropriate product for application information.


 


Note, our Copper Plate will not patina in the same fashion as real copper.


 


Basic Instructions


 


Clean the metal. (e.g...Sandblast or grind)


Immerse or spray the metal with the Copper Plate.


Rinse steel w/ water.


While steel is wet, spray on Rust Arrest and let it work for at least 15 seconds.


Rinse steel with water.


Immediately, dry steel COMPLETELY with compressed air.


Seal with Metal Finishes PLUS? Matte or Gloss Acrylic Sealer.


 


What If?


 


Plating peels off---------------Plating is too thick, immersion or spray time is to long


Plating is pink, not bright----Plating is too thick, immersion or spray time is to long.


Part will not plate-------------Metal being used is not a compatible alloy, or is not steel.


White spots or lines appear--Salt residue is present. Rinse part better or use Rust Arrest.


 


Technical Data


 


As with all chemicals, wear protective clothing, latex gloves, eye protection and avoid breathing mist. Use adequate ventilation with a chemical respirator when spraying. No known shelf life.
VOC is under 250


 


 


 

Additional Information
color N/A
HOME | ABOUT US | SERVICES | FAQS | MY ACCOUNT | HELP | CONTACT US
3600 East Truman Road - Kansas City, MO 64127|TEL: (816) 241-5550|FAX: (816) 241-7707
1501 NW Lower Silver Lake Road - Topeka, KS 66608|TEL: (785) 233-0555|FAX: (785) 233-0566
Copyright © METAL by the FOOT, Inc. All rights reserved.